PFAS Declaration for Cable Assemblies: 8-Point Checklist

A defensible PFAS declaration for cable assemblies names PTFE, FKM seals and grease at homogeneous-material level. Use this 8-point RFQ checklist. Request ours.

The short answer: what a PFAS declaration for a cable assembly has to contain

A defensible PFAS declaration for a cable assembly lists every part number you buy, breaks the content down by homogeneous material, names each substance with its CAS or EC number, states the concentration against a named threshold, names the regulation and version it was written against, and carries a named signatory, a revision number and an expiry or next-review date. Anything less is a statement of intent, not a declaration you can file.

Here is the compressed checklist — the eight items this page expands on, and the eight lines to put in your RFQ:

  1. Scope by part number and variant — every length, connector series, plating, jacket compound and overmold option you actually purchase.
  2. Homogeneous-material level — not an assembly-level percentage that cannot be rolled up or down your BOM.
  3. Substance identity — chemical name plus CAS/EC number for each PFAS present, assessed against the OECD 2021 structural definition.
  4. Concentration in ppm with the threshold stated — and whether the figure is measured, calculated from material data, or inherited from an upstream declaration.
  5. Regulatory basis and version — which instrument, which version, and the date the assessment was made.
  6. Intentional versus incidental — asked as two separate questions, never one.
  7. Signature, title, revision, validity — named signatory, issue date, expiry or re-review date.
  8. Data provenance — sub-supplier declarations, in-house material data, or analytical testing. Say which.

Two things belong in the same breath. First, a one-line "PFAS free" email is not a declaration, and RoHS compliance does not answer the question: RoHS restricts ten substances and PFAS is not among them, as a 2026 review of real supplier statements points out (GlobX, EU PFAS restriction for electronic components). Second, the broad EU restriction is a proposal moving through the REACH process, not a settled in-force obligation covering your harness — read the status on ECHA's restriction registry as of the declaration date rather than from any article, including this one.

Where PFAS actually hides in the assemblies you buy

This is where most incoming declarations fail first: they cover the cable reel and stop. The material families below are the ones your supplier's declaration must account for line by line.

Material familyTypical location in a harnessWhy it needs a separate line
Fluoropolymers — PTFE, ETFE, FEP, PFAPrimary insulation, jackets, coax dielectric, tape wrapsIt is a homogeneous material in its own right; an assembly-level figure cannot be allocated to it
Fluororubber — FKM and similarO-rings, grommets, seals, strain-relief insertsUsually bought as a separate component with its own sub-supplier declaration
Fluorinated greases and anti-friction coatingsContacts, connector interfaces, crimp and mating surfacesSmall mass, frequently omitted, and often invisible on the drawing
Adhesives and backings on labels, tapes, foilsIdentification labels, shielding wrap, potting and encapsulant interfacesPurchased as catalogue items; the data sits with a distributor, not the assembler
Fire-retardant and moisture-barrier coatingsFinished assembly, PCBAs inside overmoldsApplied late in the process, so it is often left out of the material review

The list is not theoretical. Beckhoff's PFAS declaration of 23 March 2026 states that PTFE and FKM can be present "in seals/O-rings, cables, or connectors" — and the same review notes that RoHS does not cover any of it. That is the pattern to expect from a serious industrial supplier: named polymers, named locations, and an explicit statement that the substance inventory reaches past the cable.

The 8-point RFQ checklist: what to demand before you award

1. Scope by part number and variant

Ask for the declaration to list the exact orderable part numbers, not a product family. Cable length rarely changes chemistry, but jacket compound, connector series, contact plating, overmold material and seal options do. If you buy six variants of one harness and the declaration covers two, the other four are undeclared — not compliant by default.

2. Homogeneous-material level, not assembly level

A statement that "the assembly contains less than X% fluoropolymer" cannot be allocated to a material, cannot be passed to your own customer, and cannot be defended in an audit. Require one line per homogeneous material: insulation, jacket, contact plating, housing, seal, lubricant, label adhesive, coating.

3. Substance identity with CAS or EC numbers

PFAS under the OECD 2021 structural definition is a definition, not a fixed list — it captures a very large and open-ended set of substances. That is precisely why a declaration must name the substances it covers rather than assert a category. Ask for chemical name plus CAS or EC number for each PFAS identified, and for a statement of which substance inventory was screened against the definition.

4. Concentration in ppm, with the threshold named

An unqualified "below threshold" tells you nothing until you know which threshold and which regulation version it references. Require ppm values and a statement of whether each figure is measured, calculated from supplier material data, or copied from an upstream declaration.

5. Regulatory basis, version and assessment date

A declaration written to no named instrument is unfileable. Require the supplier to state whether the assessment was made against the EU REACH restriction proposal, against US TSCA Section 8(a)(7) reporting, against a customer specification, or against several — and the date the assessment was performed.

6. Intentional versus incidental, asked separately

These are different questions and must not be merged. Watch for the qualifier that companies do not intentionally add PFAS "in free or unprocessed form": that wording can carve out exactly the fluoropolymers a broad restriction would target, and in the Beckhoff example the very next sentence confirms PTFE and FKM are present. Ask for the intentional answer and the list of PFAS that are nevertheless present in the delivered part.

7. Signature, title, revision and validity

An unsigned PDF with no revision number is not auditable. Require a named signatory with title, a company stamp or equivalent, a revision number, an issue date, and an expiry or next-review date.

8. Data provenance

Ask how each material line was established: sub-supplier declaration, in-house formulation data, or analytical test. Harwin's published statement is explicitly framed around TSCA Section 8(a)(7) and states that "no routine analytical testing is implied" — which is honest and useful, because it tells the buyer they are holding a declaration, not a test report. You need the same clarity from your supplier.

How to read the declaration you get back: five checks

  • Scope check. Overlay the declaration's part list on your own open PO lines. Any variant you buy that is absent is undeclared, not compliant.
  • "Below threshold" is not "zero". A sub-threshold ppm figure is a reporting decision against a specific threshold. Write down which threshold and which regulation version it references before you file the document.
  • Derogation check. Look for exemptions and transition periods being relied on. Commentary on the EU proposal describes multi-year transition periods for some sectors beyond 2029 (IntegrityNext, PFAS regulation in the EU) — verify any such period against the official proposal text and its current status, not against a summary.
  • Date check. A declaration issued before the last material change on your part, or before the regulation version you are being audited against, is stale. Put a re-issue trigger in the contract.
  • Chain check. Ask who upstream supplied each material line. Where transparency breaks down, those same compliance commentators identify escalation or targeted testing as the realistic fallback — plan for it rather than assuming a clean answer will arrive.

Red flags that should stop an award

  • A single sentence "PFAS free" with no CAS numbers, no material breakdown and no signatory.
  • A declaration that covers cable only, with no connector, seal, grease or overmold content.
  • A blanket "no intentional addition" statement with no accompanying list of the fluoropolymers that are nevertheless present.
  • Substance data given at assembly level, so it cannot be attributed to a homogeneous material.
  • An issue date earlier than the latest revision of the regulation you are audited against.
  • Refusal or inability to break the declaration down to homogeneous materials when asked a second time.

When the supplier cannot answer: a workable verification path

There is currently no specific PFAS testing mandate in the EU or US markets, which is why declarations carry so much weight. UL Solutions' PFAS FAQ for the electrical and electronic industry notes that no specific testing requirements exist in either market, and that a supplier declaration of no intentional use combined with non-detectable test reports for target PFAS and fluorine can serve as effective risk mitigation (UL Solutions, PFAS FAQs).

Treat fluorine screening as a screen, not a verdict. UL qualifies its reliability with "it depends": a non-detect only carries weight when paired with a declaration of no intentional use, and it will not tell you which PFAS was present. For targeted third-party testing, agree the sampling conditions, the substance list and the reporting threshold in writing with the lab before work starts — those three variables determine whether the report is usable, and none of them should be assumed.

Then close the loop commercially: a named technical contact, a written response deadline, and a re-declaration trigger on any material or sub-supplier change. On new designs, ask engineering whether a non-fluoropolymer insulation or seal meets the temperature and chemical-resistance requirement — the cheapest declaration is the one you never need. Finally, be clear about the limit of this page: it is a document-quality checklist, not a legal determination. Applicability to your product remains your own regulatory assessment, made with your counsel or notified body.

What our PFAS declaration pack covers — and what it does not

Our pack is scoped to what you order: the part numbers and variants on your list, the material families in your drawing, the regulatory basis you name, the issue date and the signatory. It states, line by line, whether the data came from us or from an upstream connector, compound or lubricant manufacturer.

What it cannot do is turn an upstream declaration into a compliance guarantee. Some material data — particularly connector inserts, plating chemistries and specialty greases — arrives from sub-suppliers at different times, so per-line response times vary. We declare what is reported to us and label it as such.

To get an accurate answer, send your open PO list or target part numbers with length, connector and jacket options, and tell us which instrument you are being audited against. Request our PFAS declaration pack and a quote for your cable assembly — include a sample request if you need the physical part alongside the paperwork, and we will scope the declaration to exactly what you buy rather than to a product family.

Frequently asked questions

Is a RoHS-compliant cable assembly automatically PFAS-free?

No. RoHS restricts ten substances and PFAS is not among them, so a RoHS-compliant part says nothing about fluoropolymers. PFAS and RoHS are separate documentation tracks and you need both.

Does "below the reporting threshold" mean the cable contains no PFAS?

No. It means the reported concentration sits under a specific threshold defined by a specific instrument and version. Sub-threshold content is still content, and the threshold reference must be recorded with the declaration.

Is a fluorine screening test enough to prove a cable assembly is PFAS-free?

Not on its own. UL Solutions describes fluorine screening as reliable only "it depends" — a non-detect is meaningful when combined with a supplier declaration of no intentional use, and it does not identify which PFAS was present.

Which parts of a cable assembly most often contain PFAS — the cable or the connectors?

Both, plus the material nobody draws: PTFE and ETFE insulation and jackets in the cable, FKM seals and grommets at connectors and backshells, and fluorinated grease on contacts. Declarations that stop at the cable reel are the most common gap we see.

Is the EU PFAS restriction already in force, and does it apply to my cable assemblies?

The broad EU restriction is a proposal progressing through the REACH process, not a settled in-force obligation for harnesses. Check the current status and scope on ECHA's restriction registry as of the date on the declaration you are relying on, and confirm applicability with your own regulatory assessment.

Request a quote

Share a model or describe your application. Include a drawing link if you have one.